Ferrari GTC4Lusso 2016-2021 Torque Specifications
Ferrari GTC4Lusso 2016-2021

Ferrari GTC4Lusso 2016-2021 Torque Specifications

Complete Ferrari GTC4Lusso 2016-2021 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.9l Twin Engine

Torque specifications for 3.9L-TWIN Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure proper bearing alignment.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure the connecting rod bearings are properly seated before tightening.
3

Flywheel Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned with the timing marks.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
Ensure the pulley/balancer is properly seated before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to prevent warping.
3

Throttle Body Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the throttle body is properly aligned before tightening.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the fuel rail is properly seated before tightening.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the thermostat housing is properly seated before tightening.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Follow the manufacturer's specified torque sequence.
2

Turbocharger Oil Feed Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Ensure proper sealing to prevent oil leaks.
3

Turbocharger Oil Return Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Ensure proper sealing to prevent oil leaks.
4

Turbocharger Coolant Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Ensure proper sealing to prevent coolant leaks.

3.9l Twin Turbo Engine

Torque specifications for 3.9L-TWIN-TURBO Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure proper bearing alignment.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure the connecting rod bearings are properly seated before tightening.
3

Flywheel Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned with the timing marks.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
Ensure the pulley/balancer is properly seated before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to prevent warping.
3

Throttle Body Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the throttle body is properly aligned before tightening.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the fuel rail is properly seated before tightening.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the thermostat housing is properly seated before tightening.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Follow the manufacturer's specified torque sequence.
2

Turbocharger Oil Feed Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Ensure proper sealing to prevent oil leaks.
3

Turbocharger Oil Return Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Ensure proper sealing to prevent oil leaks.
4

Turbocharger Coolant Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar turbocharger systems. Ensure proper sealing to prevent coolant leaks.

6.3l Engine

Torque specifications for 6.3L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure proper crankshaft alignment.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure the connecting rod bearings are properly seated before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure a proper seal.
2

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to prevent warping.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Replace the crush washer to ensure a proper seal.

Body

Torque specifications for Body

Wheels And Suspension

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
94 ft-lbs (128 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern to avoid warping the brake rotor.
2

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure suspension is at ride height before final torque application.
3

Control Arm Bolts

M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure suspension is at ride height before final torque application.
4

Ball Joint Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.
5

Tie Rod End Nut

M12 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure proper alignment of the tie rod end before tightening.
6

Sway Bar Link Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sway bar link is properly aligned before tightening.
7

Steering Gear/Rack Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the steering rack is properly aligned before tightening.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the fuel tank is properly supported before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the fuel filler neck is properly aligned before tightening.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure the battery terminals are clean and properly seated before tightening.

Body And Interior

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the door is properly aligned before tightening.
2

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the hood is properly aligned before tightening.
3

Trunk Lid Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the trunk lid is properly aligned before tightening.
4

Seat Mounting Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the seat is properly aligned before tightening.
5

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the bumper is properly aligned before tightening.
6

Roof Panel Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the roof panel is properly aligned before tightening.
7

Mirror Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the mirror is properly aligned before tightening.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure the caliper is properly aligned with the rotor before tightening.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure the bracket is properly seated against the steering knuckle or hub assembly.

Brake Rotor System

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Ensure the rotor is properly seated against the hub before tightening.

Wheel And Hub System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
94 ft-lbs (128 N·m)
Important Notes
Always use a torque wrench to ensure proper tightening. Over-tightening can damage the threads or warp the rotor.

Brake Hydraulic System

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the sealing washers are properly seated before tightening.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the master cylinder is properly aligned with the brake booster.
3

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the brake booster is properly aligned with the firewall.

Brake Pedal System

1

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the brake pedal operates smoothly after tightening.

Abs System

1

ABS Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is properly aligned with the tone ring.

Drivetrain

Torque specifications for Drivetrain

Flywheel And Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to evenly distribute load.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on similar clutch systems. Ensure bolts are tightened evenly to avoid warping the pressure plate.

Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing of the oil pan gasket.
3

Transmission Drain Plug

M12 x 1.75
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Replace the crush washer to prevent leaks.
4

Transmission Fill Plug

M12 x 1.75
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Replace the crush washer to prevent leaks.

Drive Axles And Cv Joints

1

Drive Axle/Half Shaft Bolts

M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure proper alignment of the drive axles before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Use a torque wrench with a high-capacity range for this nut.

Propeller Shaft

1

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the drive shaft before tightening.

Differential And Transfer Case

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value based on similar drivetrain systems. Ensure proper alignment before tightening.
2

Differential Drain Plug

M12 x 1.75
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Replace the crush washer to prevent leaks.
3

Differential Fill Plug

M12 x 1.75
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Replace the crush washer to prevent leaks.
4

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value based on similar drivetrain systems. Ensure proper alignment before tightening.
5

Transfer Case Drain Plug

M12 x 1.75
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Replace the crush washer to prevent leaks.
6

Transfer Case Fill Plug

M12 x 1.75
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Replace the crush washer to prevent leaks.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the ignition coil is properly seated before torquing.

Starting System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel.

Charging System

1

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the alternator is properly aligned with the drive belt.

Battery System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure the terminals are clean and free of corrosion before tightening.

Ac System

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the compressor is properly aligned with the drive belt.
2

A/C Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the fittings are clean and free of debris before tightening.

Grounding System

1

Ground Strap Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the grounding surface is clean and free of corrosion.

Engine Management System

1

ECU Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ECU is properly seated in its mounting bracket.
2

Sensor Mounting Bolts (e.g., Oxygen Sensor, Crankshaft Position Sensor)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the sensor is properly seated and aligned before tightening.

Electrical Distribution System

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuse box is properly seated in its mounting location.
2

Wiring Harness Clamp Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure the wiring harness is properly routed and secured.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust Manifold Headers

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper sequence to avoid warping the manifold.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper sequence to avoid warping the manifold.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.

Emissions Sensors

1

Oxygen Sensor (O2 Sensor) Mounting

M12 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
2

Downstream Emissions Sensor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment before tightening.
3

Exhaust Gas Temperature Sensor Mounting

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment before tightening.

Heat Shields

1

Catalytic Converter Heat Shield Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment before tightening.

Egr System

1

EGR Valve Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment before tightening.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper sequence to avoid warping the manifold or headers.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper sequence to avoid warping the manifold or headers.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.
4

Exhaust Flange Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.

Exhaust Support Components

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure hangers are properly aligned before tightening.
2

Oxygen Sensor Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper seal to prevent exhaust leaks.
3

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure heat shield is properly aligned before tightening.

F1 Transmission

Torque specifications for F1 Transmission

Flywheel And Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure proper alignment of the flywheel before torquing.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar clutch assemblies.

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the transmission is properly aligned with the engine before torquing.
2

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Estimated value based on similar bellhousing bolts.

Transmission Fluid System

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before torquing.
2

Transmission Drain and Fill Plugs

M12 x 1.75
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the sealing washer is in good condition before installation.

Drivetrain Connections

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the axle is properly seated in the transmission output shaft.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Use a torque wrench with a high-capacity adapter for this nut.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the driveshaft is properly aligned with the transmission output flange.

Shift Mechanism

1

Shift Linkage Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value based on similar shift linkage bolts.

Transmission Cooling

1

Transmission Cooler Line Fittings

M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar cooler line fittings.

Fuel

Torque specifications for Fuel

Fuel Delivery System

1

Fuel Rail Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Over-tightening can damage the injector seals.
3

Fuel Injector Rail Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the rail is properly aligned before tightening.
4

Fuel Pump Mounting Bolts

M10 x 1.5
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Ensure the pump is securely mounted to prevent vibrations.
5

Fuel Tank Strap Bolts

M12 x 1.75
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the tank is properly supported before tightening.
6

Fuel Filler Neck Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure a tight seal to prevent fuel vapor leaks.
7

Fuel Filter Bolt/Nut

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the filter housing is properly seated before tightening.

Fuel Pressure Components

1

High-Pressure Fuel Line Fittings

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar high-pressure fittings.
2

Low-Pressure Fuel Line Fittings

M10 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value based on similar low-pressure fittings.
3

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on similar regulator bolts.
4

Fuel Tank Sender Unit Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar sender unit bolts.

Hvac

Torque specifications for Hvac

Compressor Subsystem

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute stress.

Line Fittings Subsystem

1

A/C Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Proper torque is essential to prevent refrigerant leaks.

Evaporator Subsystem

1

Evaporator Housing Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on similar housing components.

Blower Motor Subsystem

1

Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar motor mounting bolts.

Heater Core Subsystem

1

Heater Core Inlet/Outlet Fittings

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar coolant line fittings.

Control Module Subsystem

1

HVAC Control Module Mounting Bolts

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value based on similar electronic module mounting bolts.

Condenser Subsystem

1

Condenser Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent stress on the condenser.

Suspension

Torque specifications for Suspension

Strut Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.
2

Upper Strut Mount Bolts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value based on similar components.
3

Lower Shock Mount Bolts

M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on similar components.

Control Arm Ball Joint

1

Control Arm Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
2

Ball Joint Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.

Steering System

1

Tie Rod End Nut

M12 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure the tie rod end is properly aligned before tightening.
2

Steering Gear/Rack Bolts

M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the steering rack is properly aligned with the chassis.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sway bar link is properly aligned before tightening.

Driveline

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the drive axle is properly seated before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure the CV joint is properly seated before tightening.

Subframe

1

Subframe Mounting Bolts

M14 x 1.5
Torque Specification
1. 45 ft-lbs (61 N·m) 2. 90 ft-lbs (122 N·m)
Important Notes
Follow the specified torque sequence to ensure even clamping force.

Wheel Bearing

1

Wheel Bearing Hub Bolts

M12 x 1.5
Torque Specification
110 ft-lbs (149 N·m)
Important Notes
Ensure the wheel bearing hub is properly seated before tightening.

Trailing Arm

1

Trailing Arm Bolts

M12 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the trailing arm is properly aligned before tightening.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque specification for the lug nuts on a 2016-2021 Ferrari gtc4lusso?

The recommended torque for wheel lug nuts IS 130 Nm (96 lb-ft) as per Ferrari technical specifications.

Q2

What type of torque wrench IS recommended for ensuring accurate torque application on a Ferrari gtc4lusso?

It IS highly recommended to use a calibrated click-type torque wrench with a range suitable for the specified torque values. Digital torque wrenches or torque multipliers can also be considered for greater precision.

Q3

IS it necessary to re-torque the lug nuts after driving a certain distance?

Yes, it IS considered best practice to re-torque the lug nuts after driving approximately 100 km (60 miles) to ensure they remain securely tightened. This IS especially important after installing new wheels or changing tires.

Q4

What are the potential consequences of over-tightening or under-tightening the bolts on a Ferrari gtc4lusso?

Over-tightening can lead to stripped threads, bolt damage, and even component failure. Under-tightening can cause loose connections, vibrations, and potential safety hazards.

Q5

Are there any specific torque sequences or patterns that need to be followed when tightening bolts on a Ferrari gtc4lusso?

Yes, it IS crucial to follow the specified torque sequence and pattern provided in the Ferrari gtc4lusso service manual. This ensures even distribution of force and prevents uneven loading on components.

Q6

What precautions should be taken when working with carbon fiber or aluminum components that require torque application?

Extra care IS necessary when handling carbon fiber or aluminum components. Ensure that the proper torque values are used as these materials are more susceptible to damage from over-tightening. Also, use torque wrenches with appropriate tips to prevent damaging the surface of the components.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the Gtc4Lusso.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Ferrari Specs. All rights reserved.

Privacy Policy Terms of Service