Ferrari 599 2007-2012 Torque Specifications
Ferrari 599 2007-2012

Ferrari 599 2007-2012 Torque Specifications

Complete Ferrari 599 2007-2012 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

6.0l Engine

Torque specifications for 6.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 26 ft-lbs (35 N·m) 2. 90°
Important Notes
Torque sequence must be followed as per manufacturer guidelines. Final step involves a 90-degree angle tighten.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure even tightening to prevent leaks.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Follow the specified torque sequence to ensure proper alignment.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
43 ft-lbs (58 N·m)
Important Notes
Ensure proper alignment of connecting rods before tightening.

Timing System

1

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
75 ft-lbs (101 N·m)
Important Notes
Ensure proper alignment of timing marks before tightening.
2

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Follow the specified torque sequence to ensure proper sealing.
2

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment and sealing of the exhaust manifold/headers.

Accessories

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment of the starter motor before tightening.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper belt tension before tightening.

Body

Torque specifications for Body

Wheels And Brakes

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Use a star pattern for tightening sequence to ensure even pressure.
2

Brake Caliper Bolts

M10 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure caliper is properly aligned before tightening.
3

Brake Caliper Mounting Bracket Bolts

M12 x 1.25
Torque Specification
116 ft-lbs (157 N·m)
Important Notes
Ensure bracket is seated properly before tightening.
4

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
38 ft-lbs (51 N·m)
Important Notes
Ensure disc/drum is seated properly before tightening.

Suspension And Steering

1

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
53 ft-lbs (72 N·m)
Important Notes
Ensure strut/shock is properly aligned before tightening.
2

Control Arm Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure control arm is properly seated before tightening.
3

Ball Joint Nut

M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure ball joint is properly seated before tightening.
4

Tie Rod End Nut

M8 x 1.25
Torque Specification
43 ft-lbs (58 N·m)
Important Notes
Ensure tie rod end is properly seated before tightening.
5

Sway Bar Link Nut

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure sway bar link is properly seated before tightening.
6

Steering Gear/Rack Bolts

M10 x 1.25
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure steering gear/rack is properly aligned before tightening.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure fuel tank is properly seated before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure filler neck is properly aligned before tightening.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure terminals are clean and properly seated before tightening.

Safety System

1

Seat Belt Anchorage Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure seat belt anchorage is properly aligned before tightening.

Body Panels

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure door is properly aligned before tightening.
2

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure hood is properly aligned before tightening.
3

Trunk Lid Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure trunk lid is properly aligned before tightening.
4

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure bumper is properly aligned before tightening.
5

Roof Panel Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure roof panel is properly aligned before tightening.

Exterior Accessories

1

Windshield Wiper Arm Nut

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure wiper arm is properly aligned before tightening.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure caliper is properly aligned before tightening.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
116 ft-lbs (157 N·m)
Important Notes
Critical for maintaining structural integrity of the braking system.

Brake Rotor System

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
38 ft-lbs (51 N·m)
Important Notes
Ensure rotor is seated properly on the hub before tightening.

Brake Hydraulic System

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new sealing washers to prevent leaks.
2

Brake Bleeder Screw

M8 x 1.25
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Avoid overtightening to prevent damage to the screw or caliper.

Brake Pedal And Master Cylinder

1

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure master cylinder is properly aligned before tightening.
2

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure pedal operates smoothly after tightening.

Wheel And Lug Nuts

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Use a star pattern to ensure even tightening.

Drivetrain

Torque specifications for Drivetrain

Engine And Flywheel

1

Flywheel Bolts

M10 x 1.25
Torque Specification
67 ft-lbs (90 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to evenly distribute load.
2

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Use a holding tool to prevent crankshaft rotation during tightening.
3

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even pressure on the clutch disc.

Transmission And Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure transmission is properly aligned before tightening bolts.
2

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure bellhousing is properly aligned with the engine block.
3

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Over-tightening can damage the oil pan gasket.
4

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use a new crush washer to ensure a proper seal.

Driveshaft And Axles

1

Drive Axle/Half Shaft Bolts

M12 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure proper alignment of the axle before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
217 ft-lbs (294 N·m)
Important Notes
Use a holding tool to prevent axle rotation during tightening.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure driveshaft is properly aligned before tightening.

Differential And Transfer Case

1

Differential Mounting Bolts

M12 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure differential is properly aligned before tightening.
2

Transfer Case Mounting Bolts

M12 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure transfer case is properly aligned before tightening.
3

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use a new crush washer to ensure a proper seal.
4

Transfer Case Drain/Fill Plug

M12 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use a new crush washer to ensure a proper seal.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the ignition coil is properly seated before torquing.

Starting System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel before torquing.

Charging System

1

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the alternator is properly aligned with the drive belt before torquing.

Battery System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the battery terminals are clean and free of corrosion before torquing.

Ac System

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Ensure the A/C compressor is properly aligned with the drive belt before torquing.
2

A/C Line Fittings

M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the A/C lines are properly aligned before torquing.

Grounding System

1

Ground Strap Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the ground strap is properly seated and free of corrosion before torquing.

Ecu System

1

ECU Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the ECU is properly seated before torquing.

Fuse Box System

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the fuse box is properly seated before torquing.

Sensor System

1

Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the sensor is properly seated before torquing.

Wiring Harness System

1

Wiring Harness Clamp Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the wiring harness is properly routed before torquing.

Emissions Sensors

Torque specifications for Emissions_sensors

Egr System

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the EGR valve is properly aligned before tightening.

Exhaust Manifold

1

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a crisscross pattern to ensure even pressure distribution.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the manifold is properly seated before tightening.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the exhaust pipe is properly aligned before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the catalytic converter is properly aligned before tightening.

Oxygen Sensors

1

Oxygen Sensor (O2 Sensor) Mounting

M12 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on similar sensor mounting specifications.

Heat Shields

1

Catalytic Converter Heat Shield Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar heat shield mounting specifications.

Temperature Sensors

1

Exhaust Gas Temperature Sensor Mounting

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar sensor mounting specifications.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Exhaust Hangers

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical M8 bolt torque specifications.

Oxygen Sensor

1

Oxygen Sensor Fittings

M12 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure sensor threads are clean and free of debris before installation.

Heat Shield

1

Heat Shield Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on typical M6 bolt torque specifications.

F1 Transmission

Torque specifications for F1 Transmission

Flywheel And Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
67 ft-lbs (90 N·m)
Important Notes
Ensure proper alignment of the flywheel before tightening.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the clutch disc is properly centered before tightening.

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure the transmission is properly aligned with the engine before tightening.
2

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure proper alignment of the bellhousing with the engine block.

Transmission Fluid System

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Transmission Drain Plug

M12 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Replace the crush washer during installation to prevent leaks.
3

Transmission Cooler Line Fittings

M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the cooler lines before tightening.

Drivetrain Components

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure proper alignment of the drive axles before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
217 ft-lbs (294 N·m)
Important Notes
Use a torque wrench with a high-capacity range for this application.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment of the driveshaft before tightening.

Electrical And Control

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment of the starter motor with the flywheel.
2

Transmission Control Module (TCM) Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper electrical connections before tightening.

Fuel

Torque specifications for Fuel

Fuel Rail System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure injectors are properly seated before tightening.

Fuel Pump And Tank System

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the fuel pump is properly aligned before tightening.
2

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the fuel tank is properly supported before tightening.
3

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the filler neck is properly aligned with the fuel tank.
4

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the sender unit is properly seated before tightening.

Fuel Filter And Lines

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the fuel filter is properly aligned before tightening.
2

Fuel Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure fittings are properly aligned and seated before tightening.
3

Fuel Return Line Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the return line is properly aligned before tightening.
4

Fuel Vent Line Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the vent line is properly aligned before tightening.

Fuel Pressure Regulator

1

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.25
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute clamping force.

Ac Lines

1

A/C Line Fittings

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use a backup wrench to prevent twisting of the refrigerant lines during tightening.

Evaporator Housing

1

Evaporator Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Heater Core

1

Heater Core Inlet/Outlet Fittings

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use a backup wrench to prevent damage to the heater core during tightening.

Hvac Control Panel

1

HVAC Control Panel Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Condenser

1

Condenser Mounting Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute clamping force.

Suspension

Torque specifications for Suspension

Strut Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M10 x 1.5
Torque Specification
53 ft-lbs (72 N·m)
Important Notes
Ensure bolts are tightened evenly to maintain alignment.
2

Upper Strut Mount Bolts

M8 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on similar components.
3

Lower Shock Mounting Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value based on similar components.

Control Arm

1

Control Arm Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure bolts are tightened evenly to maintain suspension geometry.
2

Ball Joint Nut

M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure the nut is tightened to prevent play or binding.

Steering

1

Tie Rod End Nut

M8 x 1.25
Torque Specification
43 ft-lbs (58 N·m)
Important Notes
Ensure the nut is tightened to prevent steering play.
2

Steering Knuckle Bolts

M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Estimated value based on similar components.

Sway Bar

1

Sway Bar Link Nut

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the nut is tightened to prevent sway bar play.
2

Sway Bar Bracket Bolts

M6 x 1.0
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on similar components.

Wheel

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
1. 50 ft-lbs (68 N·m) 2. 90°
Important Notes
Follow the torque sequence to ensure even tightening.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent vibration.
2

CV Joint/Axle Nut

M16 x 1.5
Torque Specification
217 ft-lbs (294 N·m)
Important Notes
Ensure the nut is tightened to prevent wheel separation.

Subframe

1

Subframe Mounting Bolts

M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Estimated value based on similar components.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque value for the crankshaft bolt on a 2009 Ferrari 599?

The crankshaft bolt on a 2009 Ferrari 599 should be tightened to a torque of 540 Nm or 398 lb-ft using a torque wrench.

Q2

What IS the correct tightening sequence for the cylinder head bolts on a 2010 Ferrari 599?

The cylinder head bolts on a 2010 Ferrari 599 should be tightened in 3 stages: 1st stage to 30 Nm (22 lb-ft), 2nd stage to 90 Nm (66 lb-ft), and 3rd stage to 120 Nm (89 lb-ft). Additionally, it IS recommended to use a new set of cylinder head bolts for each assembly.

Q3

What type of torque wrench should be used when tightening bolts on a Ferrari 599?

Always use a high-quality torque wrench with a calibration certificate when tightening bolts on a Ferrari 599. This ensures accurate and precise torque application, which IS crucial for the proper assembly and performance of the vehicle.

Q4

What are the torque specifications for the exhaust manifold bolts on a 2007 Ferrari 599?

The exhaust manifold bolts on a 2007 Ferrari 599 should be tightened to a torque of 40 Nm (30 lb-ft).

Q5

How often should the torque of the wheel bolts be checked on a Ferrari 599?

The torque of the wheel bolts should be checked every 5,000 kilometers or 3,000 miles, or more frequently if the vehicle IS driven in harsh conditions.

Q6

What are the torque specifications for the brake caliper mounting bolts on a 2012 Ferrari 599?

The front brake caliper mounting bolts should be tightened to a torque of 120 Nm (89 lb-ft) and the rear brake caliper mounting bolts should be tightened to a torque of 140 Nm (103 lb-ft).

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Recommended digital torque wrench with a range suitable for various applications on the Ferrari 599.

  • Digital display for precise readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Ferrari Specs. All rights reserved.

Privacy Policy Terms of Service