Ferrari 430 2005-2009 Torque Specifications
Ferrari 430 2005-2009

Ferrari 430 2005-2009 Torque Specifications

Complete Ferrari 430 2005-2009 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

4.3l Engine

Torque specifications for 4.3L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to avoid warping the cylinder head.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the connecting rod bearings are properly installed before tightening.

Timing System

1

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to avoid warping the manifold.
2

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Replace the crush washer to ensure a proper seal.

Body

Torque specifications for Body

Suspension And Steering

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Use a star pattern for tightening to ensure even load distribution.
2

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the vehicle is on a level surface before tightening.
3

Control Arm Bolts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Ensure suspension is at ride height before final torque.
4

Ball Joint Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.
5

Tie Rod End Nut

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the tie rod end is properly aligned before tightening.
6

Sway Bar Link Nut

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sway bar is properly aligned before tightening.
7

Steering Gear/Rack Bolts

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the steering rack is properly aligned before tightening.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the filler neck is properly aligned before tightening.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the terminals are clean and properly seated before tightening.

Body Panels And Attachments

1

Body Panel Bolts (e.g., fender, door, hood, trunk)

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on typical body panel bolt sizes. Ensure panels are properly aligned before tightening.
2

Seat Mounting Bolts

M10 x 1.25
Torque Specification
46 ft-lbs (62 N·m)
Important Notes
Estimated value based on typical seat mounting bolt sizes. Ensure seats are properly aligned before tightening.
3

Door Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical door hinge bolt sizes. Ensure doors are properly aligned before tightening.
4

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical hood hinge bolt sizes. Ensure the hood is properly aligned before tightening.
5

Trunk Lid Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical trunk lid hinge bolt sizes. Ensure the trunk lid is properly aligned before tightening.
6

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical bumper mounting bolt sizes. Ensure the bumper is properly aligned before tightening.
7

Roof Panel Bolts (if applicable)

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on typical roof panel bolt sizes. Ensure the roof panel is properly aligned before tightening.
8

Mirror Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on typical mirror mounting bolt sizes. Ensure mirrors are properly aligned before tightening.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the caliper is properly aligned before tightening. Torque in a crisscross pattern.
2

Brake Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Ensure the bracket is securely attached to the steering knuckle or hub assembly.

Brake Rotor Drum System

1

Brake Disc/Drum Retaining Bolts

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the rotor/drum is properly seated on the hub before tightening.

Brake Hydraulic System

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the sealing washers are properly installed to prevent leaks.
2

Brake Bleeder Screw

M8 x 1.25
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Avoid overtightening to prevent damage to the screw or caliper.
3

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the master cylinder is properly aligned with the brake booster or firewall.

Brake Pedal System

1

Brake Pedal Assembly Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the pedal assembly is properly aligned with the master cylinder pushrod.

Wheel Attachment System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Always torque lug nuts in a star pattern to ensure even clamping force.

Drivetrain

Torque specifications for Drivetrain

Engine Transmission Interface

1

Flywheel Bolts

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to evenly distribute torque.
2

Crankshaft Pulley/Harmonic Balancer Bolt

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the crankshaft is properly secured before applying torque.
3

Transmission Bellhousing Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute torque.

Transmission Assembly

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the transmission is properly aligned before tightening.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Avoid overtightening to prevent damage to the oil pan.
3

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the sealing washer is in good condition before installation.

Driveshaft And Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
159 ft-lbs (215 N·m)
Important Notes
Ensure the axle nut is properly seated and staked after tightening.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the driveshaft is properly aligned before tightening.

Differential And Transfer Case

1

Differential Mounting Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the differential is properly aligned before tightening.
2

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sealing washer is in good condition before installation.
3

Transfer Case Mounting Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the transfer case is properly aligned before tightening.
4

Transfer Case Drain/Fill Plug

M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the sealing washer is in good condition before installation.

Clutch Assembly

1

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the pressure plate is properly aligned before tightening.

Rear Axle Assembly

1

Rear Axle Hub Bolts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Ensure the hub is properly seated before tightening.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the ignition coil is properly seated before tightening.
2

Spark Plug

M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a spark plug socket to avoid damaging the plug.

Battery System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure terminals are clean and free of corrosion before tightening.
2

Battery Grounding Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar grounding bolts.

Charging System

1

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 37 ft-lbs (50 N·m)
Important Notes
Follow the specified torque sequence to ensure proper alignment.

Starting System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 37 ft-lbs (50 N·m)
Important Notes
Follow the specified torque sequence to ensure proper alignment.

Electrical Distribution

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar electrical components.
2

Wiring Harness Connector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on similar electrical components.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust Manifold

1

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Standard torque value for exhaust manifold bolts.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Standard torque value for securing the manifold to the cylinder head.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Standard torque value for exhaust pipe connections.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Standard torque value for catalytic converter connections.

Emissions Sensors

1

Oxygen Sensor Mounting Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Standard torque value for oxygen sensor mounting.
2

Exhaust Temperature Sensor Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Standard torque value for temperature sensor mounting.

Emissions Control

1

EGR Valve Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Standard torque value for EGR valve mounting.
2

Emissions Control Module Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Standard torque value for emissions control module mounting.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper sequence to avoid warping the manifold or damaging the gasket.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure a secure connection to prevent leaks at this critical junction.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening.

Muffler

1

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening.

Heat Shield

1

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value based on typical heat shield bolt sizes.

Oxygen Sensor

1

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.

Exhaust Flange

1

Exhaust Flange Bolts (Mid-Pipe Connection)

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening.

Exhaust Hanger

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on typical exhaust hanger bolt sizes.

F1 Transmission

Torque specifications for F1 Transmission

Flywheel

1

Flywheel Bolts

M12 x 1.5
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Critical for high-speed operation. Ensure bolts are evenly tightened.

Transmission Mounting

1

Transmission Mounting Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Low torque required to prevent oil pan deformation.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent axle slippage.
2

CV Joint/Axle Nut

M18 x 1.5
Torque Specification
159 ft-lbs (215 N·m)
Important Notes
High torque required to prevent disengagement during operation.

Drive Shaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent vibration.

Starter Motor

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened evenly for reliable starter operation.

Clutch

1

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent clutch slippage.

Bellhousing

1

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.

Shift Fork

1

Shift Fork Pivot Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure bolts are tightened evenly for smooth gear changes.

Input Shaft

1

Transmission Input Shaft Retaining Nut

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure nut is tightened to specified torque to prevent shaft slippage.

Output Shaft

1

Transmission Output Shaft Flange Bolts

M10 x 1.5
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent flange leaks.

Fuel

Torque specifications for Fuel

Fuel Delivery System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the fuel rail is properly aligned before tightening to avoid damaging fuel lines or injectors.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the injector is properly seated before tightening to prevent fuel leaks.
3

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fuel pump is properly aligned with the fuel tank before tightening.

Fuel Tank And Related Components

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the fuel tank is properly positioned before tightening to prevent stress on the tank or straps.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the filler neck is properly aligned with the fuel tank before tightening.
3

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the sender unit is properly seated to prevent fuel leaks and ensure accurate fuel level readings.

Fuel Filtration And Pressure Regulation

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel filter is properly aligned before tightening to prevent leaks.
2

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the pressure regulator is properly seated before tightening to prevent leaks.

Evaporative Emission System

1

EVAP Canister Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the EVAP canister is properly aligned before tightening to prevent leaks.
2

Fuel Tank Vent Valve Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the vent valve is properly seated before tightening to prevent leaks.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute clamping force.

Ac Lines

1

A/C Line Fittings

M8 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a torque wrench to avoid overtightening, which can damage the fittings.

Blower Motor

1

HVAC Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the blower motor is properly aligned before tightening bolts.

Condenser

1

HVAC Condenser Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure distribution.

Evaporator Core

1

HVAC Evaporator Core Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Avoid overtightening to prevent damage to the evaporator core housing.

Duct Connectors

1

HVAC Duct Connector Bolts

M5 x 0.8
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure airtight seals to prevent airflow leaks.

Suspension

Torque specifications for Suspension

Strut Shock Absorber System

1

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.
2

Upper Strut Mount Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on similar M8 bolt applications.
3

Lower Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.

Control Arm System

1

Control Arm Bolts

M12 x 1.75
Torque Specification
1. 50 ft-lbs (68 N·m) 2. 90°
Important Notes
Follow the torque sequence to ensure even load distribution.
2

Ball Joint Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.

Steering System

1

Tie Rod End Nut

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the tie rod end is properly seated before tightening.
2

Steering Gear/Rack Bolts

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Follow the torque sequence to ensure even load distribution.
3

Steering Knuckle Bolts

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the steering knuckle is properly aligned before tightening.

Sway Bar System

1

Sway Bar Link Nut

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sway bar link is properly seated before tightening.

Subframe System

1

Subframe Mounting Bolts

M14 x 2.0
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Follow the torque sequence to ensure even load distribution.

Rear Suspension System

1

Rear Suspension Trailing Arm Bolts

M14 x 2.0
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Ensure the trailing arm is properly aligned before tightening.

Wheel System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Use a star pattern to tighten lug nuts evenly.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the torque specifications for the lug nuts on my 2008 Ferrari 430?

Lug nuts should be tightened to 118 ft-lbs (160 Nm) using a torque wrench. Refer to the vehicle's owner's manual for specific torque values.

Q2

What type of torque wrench should I use for critical suspension components on my 2005 Ferrari 430?

Use a calibrated, click-type torque wrench that meets or exceeds industry standards. Ensure the wrench IS within its specified torque range and has been recently calibrated.

Q3

How do I properly measure torque when using an analog torque wrench?

Set the wrench to the desired torque value. Hold the wrench perpendicular to the fastener and apply force smoothly until the wrench 'clicks' or reaches the desired torque.

Q4

Can I use impact tools to tighten critical bolts on my Ferrari 430?

No. Impact tools should not be used to tighten critical bolts on a Ferrari 430. Excessive force can damage bolts, threads, and components.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the 430.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Engine Cylinder Head Bolt Torque Sequence

Technical procedure for tightening cylinder head bolts in proper sequence and torque specifications for Ferrari 430

  • Clean the bolt threads and mating surfaces thoroughly.
  • Lubricate the bolt threads with a suitable thread lubricant.
  • Tighten the bolts in the specified sequence and to the specified torque values.
  • Double-check the torque values after the engine has cooled down.
View full procedure

Suspension Component Torque Specifications

Technical procedure for tightening suspension components to correct torque specifications for Ferrari 430

  • Raise the vehicle and support it on jack stands.
  • Remove the wheels.
  • Tighten the suspension components to the specified torque values.
  • Double-check the torque values after the vehicle has been lowered.
View full procedure
Technical Service Bulletins

Service Bulletin: Incorrect Torque Specifications for Intake Manifold Bolts

2006-03-15

Detailed bulletin describing incorrect torque specifications provided in previous documentation for intake manifold bolts on Ferrari 430

2005-2006 430

Resolution: Provides revised torque specifications and instructions for affected vehicles.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Ferrari Specs. All rights reserved.

Privacy Policy Terms of Service