Ferrari 360 2000-2005 Torque Specifications
Ferrari 360 2000-2005

Ferrari 360 2000-2005 Torque Specifications

Complete Ferrari 360 2000-2005 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.6l Engine

Torque specifications for 3.6L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (24 N·m) 2. 90°
Important Notes
Torque sequence must be followed as per manufacturer guidelines. Final step involves a 90-degree angle tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
55 ft-lbs (74 N·m)
Important Notes
Ensure proper alignment of bearing caps before torquing.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper alignment of connecting rods before torquing.

Flywheel

1

Flywheel Bolts

M12 x 1.75
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure flywheel is properly aligned before torquing.

Oil System

1

Oil Pan Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure oil pan gasket is properly aligned before torquing.
2

Oil Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components.

Valve Train

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure valve cover gasket is properly aligned before torquing.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of rocker arms before torquing.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before torquing.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket before torquing.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure intake manifold gasket is properly aligned before torquing.
2

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure exhaust manifold gasket is properly aligned before torquing.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure spark plugs are properly seated before torquing.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure ignition coil is properly seated before torquing.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure water pump gasket is properly aligned before torquing.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure thermostat housing gasket is properly aligned before torquing.

Fuel System

1

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure fuel injectors are properly seated before torquing.
2

Fuel Rail Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure fuel rail is properly aligned before torquing.

Sensors

1

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure sensor is properly aligned before torquing.
2

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure sensor is properly aligned before torquing.

Body

Torque specifications for Body

Suspension And Steering

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
94 ft-lbs (128 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern to evenly distribute torque.
2

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure suspension is at ride height before final torque application.
3

Control Arm Bolts

M12 x 1.75
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure suspension is at ride height before final torque application.
4

Ball Joint Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the ball joint before tightening.
5

Tie Rod End Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the tie rod end before tightening.
6

Sway Bar Link Nut

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure sway bar is properly aligned before tightening.
7

Steering Gear/Rack Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure steering gear is properly aligned before tightening.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure fuel tank is properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure fuel filler neck is properly aligned before tightening.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure battery terminals are clean and free of corrosion before tightening.

Body Panels And Fixtures

1

Body Panel Bolts (e.g., fender, door, hood, trunk)

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on typical body panel bolt sizes. Ensure panels are properly aligned before tightening.
2

Seat Mounting Bolts

M10 x 1.25
Torque Specification
41 ft-lbs (56 N·m)
Important Notes
Estimated value based on typical seat mounting bolt sizes. Ensure seats are properly aligned before tightening.
3

Door Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on typical door hinge bolt sizes. Ensure doors are properly aligned before tightening.
4

Hood Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on typical hood hinge bolt sizes. Ensure hood is properly aligned before tightening.
5

Trunk Lid Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on typical trunk lid hinge bolt sizes. Ensure trunk lid is properly aligned before tightening.
6

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on typical bumper mounting bolt sizes. Ensure bumper is properly aligned before tightening.
7

Roof Panel Bolts (if applicable)

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on typical roof panel bolt sizes. Ensure roof panel is properly aligned before tightening.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure proper alignment of the caliper before tightening.
2

Brake Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
Ensure the bracket is properly seated before tightening.
3

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the sealing washers are in good condition and properly seated.

Brake Rotor System

1

Brake Disc Retaining Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the rotor is properly seated on the hub before tightening.

Brake Hydraulic System

1

Brake Bleeder Screw

M8 x 1.25
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Over-tightening can damage the screw or caliper.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the master cylinder is properly aligned before tightening.

Brake Pedal System

1

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the pedal assembly is properly aligned before tightening.

Wheel Attachment System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
94 ft-lbs (128 N·m)
Important Notes
Always use a torque wrench to ensure proper tightening.

Drivetrain

Torque specifications for Drivetrain

Engine To Transmission

1

Flywheel Bolts

M10 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Critical for transferring engine power to the transmission. Ensure proper sequence to avoid warping.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensures smooth clutch operation. Torque in a star pattern to avoid warping.
3

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensures proper alignment between the engine and transmission.

Transmission

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensures transmission stability and alignment.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Prevents leaks and ensures transmission fluid integrity.
3

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensures leak-free sealing for transmission fluid management.

Driveshaft And Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
41 ft-lbs (55 N·m)
Important Notes
Ensures secure attachment of drive axles to the differential or wheel hubs.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Critical for securing the CV joint to the wheel hub. Use a torque wrench with a high range.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensures secure attachment of the drive shaft to the transmission and differential.
4

Driveshaft Center Support Bearing Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensures driveshaft balance and prevents vibration.

Differential And Transfer Case

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensures differential stability and alignment.
2

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensures leak-free sealing for differential fluid management.
3

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensures transfer case stability and alignment.
4

Transfer Case Drain/Fill Plug

M12 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensures leak-free sealing for transfer case fluid management.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensures a secure connection to the cylinder head, preventing electrical arcing or misfires.

Starting System

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensures the starter motor is securely mounted, preventing misalignment or disconnection during operation.

Charging System

1

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensures the alternator is securely mounted and properly aligned with the drive belt, preventing slippage or failure.

Battery System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensures a secure electrical connection, preventing voltage drops, corrosion, or disconnection.

Ac System

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensures the compressor is securely mounted, preventing vibration or misalignment that could damage electrical connections.
2

A/C Line Fittings

M6 x 1.0
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensures a leak-free seal and maintains the integrity of the electrical connections to the compressor.

Grounding System

1

Ground Strap Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensures a secure connection, preventing electrical issues such as poor starting, dim lights, or erratic sensor behavior.

Ecu System

1

ECU Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensures the ECU is securely mounted, preventing vibration damage or electrical disconnection.

Fuse Box System

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensures the fuse box is securely mounted, preventing loose connections or electrical faults.

Sensor System

1

Sensor Mounting Bolts (e.g., Crankshaft Position Sensor, Camshaft Position Sensor)

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensures sensors are securely mounted and properly aligned, preventing inaccurate readings or failure.

Wiring Harness System

1

Wiring Harness Clamp Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensures the harness is securely held, preventing chafing, vibration damage, or electrical shorts.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust Manifold And Headers

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper torque sequence to avoid warping the manifold.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper torque sequence to avoid warping the manifold.

Exhaust Pipe And Catalytic Converter

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.

Emissions Sensors

1

O2 Sensor (Oxygen Sensor) Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
2

EGR Valve Bolts

M6 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
3

Exhaust Gas Temperature Sensor Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
4

PCV (Positive Crankcase Ventilation) Valve Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.

Heat Shields

1

Catalytic Converter Heat Shield Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the heat shield is properly aligned before tightening.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper sequence is followed to avoid warping the manifold.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper sequence is followed to avoid warping the manifold.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Exhaust Support Components

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure hangers are properly aligned before tightening.
2

Oxygen Sensor Bolts

M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure sensor is properly seated before tightening.
3

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure heat shield is properly aligned before tightening.
4

Exhaust Flange Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

F1 Transmission

Torque specifications for F1 Transmission

Flywheel And Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to avoid warping the flywheel.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar M8 bolts in high-stress applications.

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening.
2

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment between the engine and transmission.

Transmission Fluid System

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
2

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Ensure the sealing washer is in good condition.

Drivetrain Components

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
41 ft-lbs (55 N·m)
Important Notes
Ensure proper alignment of the drive axles before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Use a new cotter pin after tightening.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the propeller shaft before tightening.

Transmission Shafts

1

Transmission Input Shaft Nut

M18 x 1.5
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
Ensure the input shaft is properly seated before tightening.
2

Transmission Output Shaft Flange Bolts

M10 x 1.25
Torque Specification
41 ft-lbs (55 N·m)
Important Notes
Ensure proper alignment of the output shaft flange before tightening.

Shift Mechanism

1

Shift Linkage Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the shift linkage before tightening.

Fuel

Torque specifications for Fuel

Fuel Rail System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Fuel Injector Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Over-tightening can damage the injector seals.

Fuel Delivery System

1

Fuel Pump Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the fuel pump is properly seated before tightening.
2

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
3

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure the filler neck is properly aligned with the fuel tank.
4

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel filter is properly aligned before tightening.

Fuel Regulation System

1

Fuel Pressure Regulator Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.
2

Fuel Line Fittings

M6 x 1.0
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure the fittings are properly aligned and seated.

Fuel Tank System

1

Fuel Tank Sender Unit Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the sender unit is properly seated before tightening.
2

Fuel Cap

N/A (Hand-tightened)
Torque Specification
N/A
Important Notes
Hand-tighten the fuel cap to ensure a proper seal.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N-m)
Important Notes
Ensure the compressor is properly aligned before tightening. Torque values are estimated based on typical A/C compressor bolts.

Refrigerant Lines

1

A/C Line Fittings

M8 x 1.25
Torque Specification
13 ft-lbs (18 N-m)
Important Notes
Torque values are estimated based on typical refrigerant line fittings. Ensure fittings are clean and free of debris before assembly.

Evaporator Housing

1

Evaporator Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N-m)
Important Notes
Torque values are estimated based on typical evaporator housing bolts. Ensure the housing is properly sealed to prevent air leaks.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N-m)
Important Notes
Torque values are estimated based on typical blower motor bolts. Ensure the motor is securely mounted to prevent vibrations.

Heater Core

1

Heater Core Inlet/Outlet Fittings

M8 x 1.25
Torque Specification
11 ft-lbs (15 N-m)
Important Notes
Torque values are estimated based on typical heater core fittings. Ensure fittings are clean and free of debris before assembly.

Condenser

1

Condenser Mounting Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N-m)
Important Notes
Torque values are estimated based on typical condenser bolts. Ensure the condenser is properly aligned before tightening.

Suspension

Torque specifications for Suspension

Strut Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.
2

Upper Strut Mount Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on similar components.
3

Lower Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value based on similar components.

Control Arm Ball Joint

1

Control Arm Bolts

M12 x 1.75
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.
2

Ball Joint Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.

Steering System

1

Tie Rod End Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the tie rod end is properly seated before tightening.
2

Steering Gear/Rack Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the steering rack is properly aligned with the chassis.
3

Steering Knuckle Bolts

M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on similar components.

Sway Bar

1

Sway Bar Link Nut

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the sway bar link is properly seated before tightening.
2

Sway Bar Bracket Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on similar components.

Wheel Drivetrain

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
94 ft-lbs (128 N·m)
Important Notes
Use a star pattern to tighten lug nuts evenly.
2

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
41 ft-lbs (55 N·m)
Important Notes
Ensure the drive axle is properly seated before tightening.
3

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure the CV joint is properly seated before tightening.

Subframe

1

Subframe Mounting Bolts

M14 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Use a crisscross pattern to tighten bolts evenly.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque setting for the engine head bolts on a 2003 FERRARI 360?

As per FERRARI technical specifications, the engine head bolts on a 2003 FERRARI 360 should be torqued to 100 Nm (74 lb-ft) in a three-step sequence: 50 Nm (37 lb-ft), 80 Nm (59 lb-ft), and finally 100 Nm (74 lb-ft).

Q2

What type of torque wrench IS recommended for accurate bolt tightening on a FERRARI 360?

For precise torque application on a FERRARI 360, it IS recommended to use a high-quality, calibrated torque wrench that meets or exceeds industry standards. A click-type torque wrench or a digital torque wrench IS suitable for this purpose.

Q3

How often should the wheel lug nuts be torqued on a 2000-2005 FERRARI 360?

To ensure optimal wheel safety and performance, it IS recommended to torque the wheel lug nuts on a FERRARI 360 every time the wheels are removed or reinstalled. The recommended torque setting IS 115 Nm (85 lb-ft).

Q4

What are the torque specifications for the suspension bolts on a 2005 FERRARI 360?

The torque settings for the suspension bolts on a 2005 FERRARI 360 vary depending on the specific bolt location. Refer to the FERRARI 360 service manual for the exact torque specifications for each bolt.

Q5

Can over-tightening bolts cause damage to the FERRARI 360?

Yes, over-tightening bolts can lead to several issues. Excessive torque can damage the threads, strip the bolt head, or even cause the bolt to snap. It IS crucial to strictly adhere to the specified torque settings provided in the FERRARI service manual.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the 360.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Bolt Tightening Sequence for Engine Assembly

Step-by-step guide for proper engine assembly, including torque specifications.

  • Clean all bolt threads and apply appropriate threadlocker.
  • Tighten the cylinder head bolts in the specified sequence to 70 Nm.
  • Tighten the crankshaft pulley bolt to 180 Nm.
  • Tighten the flywheel bolts in a star pattern to 100 Nm.
  • Tighten the exhaust manifold bolts to 30 Nm.
View full procedure

Suspension Component Torque Specifications

Detailed instructions for tightening suspension components.

  • Tighten the upper control arm bolts to 120 Nm.
  • Tighten the lower control arm bolts to 180 Nm.
  • Tighten the tie rod end bolts to 60 Nm.
  • Tighten the anti-roll bar links to 80 Nm.
View full procedure
Technical Service Bulletins

TSB 002: Cylinder Head Bolt Recall

2003-05-01

Notification of a recall for faulty cylinder head bolts. Affected vehicles should be inspected and bolts replaced as necessary.

2002-2003 360

Resolution: Replace all cylinder head bolts with new, upgraded versions.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Ferrari Specs. All rights reserved.

Privacy Policy Terms of Service